MTM Pressure Washer Hose Reel | 50' Hoses

If you are looking for a complete reel/hose solution check out this kit: MTM Pressure Washer Hose Reel Kit | 50' Hose and 5' Jumper with QC

Inlet on rear is 3/8" Male(where your inlet jumper hose connects) 

Outlet on side is 3/8" Female (where your hose going on the reel connects)

These are entry level hose reels, they are a great product for the price but take a little bit of work and some other parts to set them up properly. Here is how we suggest setting these up:

The outlet for your high pressure hose is on the side and is 3/8" female. Our Kobrajet hoses with bare 3/8" male ends will connect here, we do not suggest using quick connects for this connection point.

We do HIGHLY RECCOMEND you get one of these elbow to make this connection easier: 

Cox Reels Steel 90 Degree Elbow | 3/8" Male to Female NPT

The inlet is on the back of the reel and 3/8" Male. We suggest installing one of these plugs on it:

MTM Quick Connect Plug 3/8" Female | Stainless Steel

This is where you would connect one of our jumper hoses from your pressure washer to the reel, in the length that works best for you.

You can find them here: Jumper Hoses/Whip Lines 

We suggest installing these 3/8" coupler on both ends of your jumper hose:

MTM 3/8" Female Quick Connect Coupler | Stainless Steel

The last piece you would need is a quick connect plug for the outlet of your pressure washer, we have these available in M22 14 and 15 sizes.

MTM Hydro's Hose Reels offer a consolidated and organized method for storing your KobraJet hose! Hardware is not included for mounting as this is specific to your setup, however the high grade brass swivel is recognized by many to outperform most other models in the cold water hose reel division.

Simply slide the swivel end of your Kobrajet hose through the opening provided at the side of the reel core and install the 3/8" Male NPT threads into the 3/8" Female NPT threads of the swivel. Do not make a Quick Coupling joint at the swivel as there is not enough space and the bend in the line is too severe. Be sure to allow a small amount of slack at the swivel joint and use the red hose fastener provided to secure the hose at this joint. Using a Whip Line connected to your pump, connect to the 3/8" Male NPT hose reel inlet. When planning, add an extra foot to the distance so as not to bend the Whip Line too severely. Lastly, install the handle with the hardware provided.

Before leaving your hose reel unattended, always engage the locking mechanism on the side of the reel.

This Hose reel is rated for cold water use only.

The exact dimensions on these reels can vary slightly by batch. They are currently about:

Height 16.5"

Width 15"

Depth 13.5"

Warranty Information and Technical Support Contact:

It is important you understand before purchasing an MTM Hydro brand product, the warranty is facilitated by Veloci Performance Products (the supplier/manufacturer of MTM Hydro brand products), which is the case with almost all tool and equipment purchases. Veloci warrants to the original purchaser of their pressure washing accessories that such products will be free of material and workmanship defects under normal use for the period of 90 days from purchase. The entire warranty policy can be view at the link below. In the very rare case of a warranty defect or failure with a high pressure part it will typically present itself with the first use. After the 90 day period any failure of a high pressure part is considered regular wear and tear.

Any technical issues, warranty returns or exchanges will be facilitated directly with the supplier/manufacturer, Veloci Performance Products. The Clean Garage will assist you in making contact with them and anything else within our power to make the process smooth for you should an issue arise. We suggest reviewing the manufacturers full warranty policy before purchase which can be found here: https://www.vppdealers.com/refunds

For general or customer support service related inquiries, call MTM at 866-686-4020